Loading... Please wait...

Reloading Tips & Tricks from Gunstop Reloading

Common Firearm Malfunctions Caused by Reloading Mistakes


Nothing spoils a fun afternoon of shooting quicker than firearm malfunctions and hangups. Although most reloaders don’t experience a high rate of problems, beginner handloaders can take a while to work out the kinks to get their rounds performing reliably and accurately. Here’s a short guide to some of the more common issues and what might be causing them.

Problems with Cycling

Firearms cycling – the process of loading, firing, and loading a fresh round – can get a user easily hung up on some of the more common reloading mistakes. Although semi-auto actions are the most susceptible to cycling issues, even bolt action rifles can have issues cycling if the mistakes are serious enough.

The most common causes of cycling issues include using the wrong size of cases or using bullets that are not seated and crimped correctly. Double check your cases are the right length (trim if needed) and practice seating bullets until you can get it just right.

Extraction issues can also be caused by handloading errors. If your pressures are either too high or too low, the action may not cycle correctly. Too low of a powder charge may not work the action on semi-auto firearms, and too much powder can cause excess pressure that will expand the case too much, bulging and jamming it or even rupturing it, which can be dangerous.

Things To Check

  • Case is the proper length
  • Bullet is not seated too far out of the case
  • Bullet is not crimped too loose – strong recoil can move the bullet forward
  • Bullet is not crimped too hard – this can cause bulges in the case
  • Primer is seated correctly – if the primer is sticking out it can jam actions and be dangerous
  • Powder charge is within specs for your reloading recipe

Problems with Firing

If some of your rounds aren’t going off correctly or if you experience far too much recoil compared to factory loads, you should carefully double check the following details.

A common cause for reloads not firing is having primers seated too deeply, which may cause the firing pin to not strike them hard enough to ignite.

Another possible malfunction is caused by improperly seated primers. This is known as a “hang fire,” which is the perceptible delay between the hammer hitting the primer and the bullet firing. These are caused by the powder starting to burn slowly and taking a small amount of time to build up enough pressure to fire the round. Hang fires can be dangerous; if the bullet doesn’t get enough pressure to leave the barrel it may get stuck. Check your firearm over carefully if you experience hang fires.

One other problem is excessive recoil which is usually caused by either too much powder in the reload or damaged cases. Double check you’re using the right kind of and the correct amount of powder. Double check all your cases for very small cracks near the neck or bottom since these cracks let extra gases escape and can even cause ruptured cases. Also look for dents; when a dent is large enough, it will reduce the capacity of the case, which causes too much pressure.

Things To Check

  • Primer is seated correctly – keep primer pockets clean and check depth
  • Proper kind and amount of powder – stay within specs
  • Cracks in the case – turn it over in your hand to feel for cracks
  • Dents in the case – sometimes case lube buildup can cause dents

Problems with Accuracy

Many shooters get into reloading to improve accuracy, which makes accuracy issues even more frustrating. Before you start to diagnose the problems make sure your rifle is accurate with factory loads and any optics are properly zeroed.

The first thing to check is your reloading recipe: make sure to use only well-documented and proven loads to get the most accuracy.

Many accuracy issues can be traced back to the case. Use only high-quality cases and fire form your brass for the best results. Fire forming is using cases that have been fired once through the exact rifle for which you are reloading. This expands the case to the exact dimensions of the chamber, and combined with neck only case reforming aids in accuracy.

Also make sure your powder load is accurately measured and consistent. Overloading on powder can actually decrease accuracy.

Proper bullet seating is also critical to accuracy: make sure the depth and crimp is right on. Many precision shooters choose to seat the bullet farther out for a very tight mating with the chamber. This can aid accuracy, but make sure it’s consistent and not seated too far forward.

Things To Check

  • Double check rifle is accurate with factory match loads
  • Use a high quality reloading recipe – start with a proven formula before you alter it
  • Use high quality cases – fired once through your rifle is possible
  • Make sure powder load is accurate and consistent
  • Seat bullets consistently and slightly more forward if needed

We hope these pointers help you diagnose any issues you may be experiencing, and as always, have a safe and enjoyable time shooting!

Reload Like a Pro - Better Results with Consistency

One of the holy grails of reloading is reliable, accurate, and extremely consistent rifle rounds. Getting match quality results from your own rounds which cost a fraction of factory loaded ammunition is extremely satisfying. At first, it might seem like a daunting task, but even relatively new handloaders can achieve amazing results by following some [...]

Read More »

Top Five Reasons To Start Reloading

Have you been flirting with the idea of reloading but you still need an extra push to get started? Does the process look complex and confusing and you’re lost on where to start? Whatever your reasons are for putting it off, here are some great reasons to start reloading today.It Saves You MoneyReloading can save [...]

Read More »

The Pressing Question for First Timers - What Kind of Press To Get?

If you are new to reloading the dizzying array of equipment and materials, it can be overwhelming at first. One item in particular people struggle with is their first press. The reloading press is also the most expensive component in your reloading setup, so choosing a model that works for you will ensure your investment [...]

Read More »

Hot On The Case - Figuring Out What Went Wrong by Inspecting Cases

Cases are a critical part to the reloading process: they hold all the other components together and when something goes wrong, they can provide critical clues to finding the issue. For the sake of this discussion, let’s assume you are only handloading with high-quality brass cases, designed to be reloaded and trimmed to the proper length.BulgesBulges [...]

Read More »

Bullet Basics

The bullet may arguably be the most important component of your reloading formula. It's the only part that needs to reach the target accurately and safely every time. Handloaders today are blessed with a huge variety of bullets to choose from, but that can also make the choice confusing. Here are the basics of bullet selection [...]

Read More »

How to Take Your Reloading to the Next Level

Reloading is a fun way to save money and improve your shooting, and can become a life-long hobby. But the fun doesn’t have to stop when you pull the trigger! There is a huge range of advanced reloading adventures to take on. From customizing cases to casting bullets and measuring your reload’s performance, exploring the [...]

Read More »

ATF Withdraws Plans to Ban Popular M855 Projectiles

After receiving more than 80,000 comments from the public, mostly highly critical, the ATF has withdrawn a proposal to ban the M855 steel core projectiles or so called “green tip” ammunition. Although a future ban is not out of the question, for now these highly popular projectiles will remain legal and most likely widely available.Weeks [...]

Read More »

Reloading for Hunting

Although there are many good choices for factory loaded hunting ammunition, loading your own hunting rounds can be economical, lead to better accuracy and lethality, and be just plain fun. Developing your own recipe specifically for your rifle will ensure that, when that once-in-a-lifetime shot comes up, your ammunition is up to the challenge.Cost Factory hunting [...]

Read More »

Reloading for Long-Distance Shooting

There is no feeling quite like hitting your target from a great distance away. Whether it’s ringing a gong at 900 yards, printing a 3-inch group at 400 yards or taking an antelope at 300 yards, long distance shooting is both fun and challenging. Although there are many high quality options for factory loaded ammunition when [...]

Read More »

newsletter signup

Connect with us

Credit Card Processing
Gunstop Reloading Supplies, Inc. BBB Business Review